takeoffmetric.com

# TakeoffMetric

> Construction calculators and estimating tools for contractors: concrete yards, bags, truck loads and printable takeoffs. Every sheet shows its sources.

## Tools

- [Concrete Calculator](https://takeoffmetric.com/concrete/concrete-calculator/): Concrete calculator for slabs: cubic yards with waste, bags by size, truck loads, weight and cost. Multi-section, thickened edge, exportable takeoff.
- [Rebar Calculator](https://takeoffmetric.com/concrete/rebar-calculator/): Rebar calculator for a slab grid or a continuous footing: bar count each way, lap splices, stock bars to order at 20, 40 or 60 ft, weight and cost.
- [Footing Calculator](https://takeoffmetric.com/concrete/footing-calculator/): Footing calculator that takes the continuous footing off your building footprint, on the centreline, then adds pads and piers into one concrete order.
- [Concrete Cost Calculator](https://takeoffmetric.com/concrete/concrete-cost-calculator/): Concrete slab cost calculator: your own delivered price per cubic yard on the quarter-yard order, the cost per square foot, short-load fee, delivery, and bags against a truck.
- [Gravel Calculator](https://takeoffmetric.com/earthwork/gravel-calculator/): Gravel calculator with a sourced density you can change: cubic yards, short tons and tonnes, compacted-to-loose conversion, truck loads and cost per ton.
- [Asphalt Calculator](https://takeoffmetric.com/paving/asphalt-calculator/): Asphalt calculator for hot mix: short tons and tonnes per course, up to four areas, a cited in-place unit weight you can replace, spread rate and takeoff.
- [Fill Dirt Calculator](https://takeoffmetric.com/earthwork/fill-dirt-calculator/): Fill dirt calculator for dirt coming in or going out: cubic yards, tons and truck loads from a cited federal exhibit, compacted only if you ask.
- [Sand Calculator](https://takeoffmetric.com/earthwork/sand-calculator/): Sand calculator that counts 50 lb bags as well as cubic yards and tons, with dry, damp and wet densities from a cited table and a screeded paver bedding depth.
- [Topsoil Calculator](https://takeoffmetric.com/earthwork/topsoil-calculator/): Topsoil calculator for a new lawn, a top-dressing pass, a garden bed or a raised box: cubic yards, bags, weight and coverage, less the soil already there.
- [Concrete Block Calculator](https://takeoffmetric.com/masonry/concrete-block-calculator/): Concrete block calculator: blocks from net wall area with openings deducted, plus mortar bags, masonry sand and grout by wall thickness, every figure cited.
- [Paver Base Calculator](https://takeoffmetric.com/masonry/paver-base-calculator/): Paver base calculator for crushed stone, bedding sand and the excavation depth under a patio, driveway or street, with cited minimum base thickness.
- [Roofing Calculator](https://takeoffmetric.com/roofing/roofing-calculator/): Roofing calculator: shingle bundles, underlayment rolls, ridge cap and starter from the plan footprint and pitch, each coverage figure from a named sheet.
- [Roof Pitch Calculator](https://takeoffmetric.com/roofing/roof-pitch-calculator/): Roof pitch calculator: turn a rise and run, an angle or a grade into pitch, degrees, percent and the slope factor, plus ridge height and common rafter length.
- [Wall Framing Calculator](https://takeoffmetric.com/framing/wall-framing-calculator/): Wall framing calculator: studs, plates, headers, cripples and sheathing, with every door and window laid out from its own rough opening width and position.
- [Rafter Calculator](https://takeoffmetric.com/framing/rafter-calculator/): Rafter calculator: common rafter length with the ridge board deducted, plumb, seat and birdsmouth cuts, height above plate, rafter count, hips and jacks.
- [Board Foot Calculator](https://takeoffmetric.com/framing/board-foot-calculator/): Board foot calculator for up to four lumber sizes: total board feet, the whole board feet to order, lineal feet, cost per board foot and per 1,000 board feet.
- [Deck Calculator](https://takeoffmetric.com/decks-fences/deck-calculator/): Deck material calculator: decking boards at your stock length, rows or 45 degree courses, joists, beams, posts and round footing concrete, in one takeoff.
- [Fence Calculator](https://takeoffmetric.com/decks-fences/fence-calculator/): Fence material calculator: posts by type, rails, pickets, gates and post-hole concrete from one line, with the corners and the gate openings taken off first.
- [Mortar Calculator](https://takeoffmetric.com/masonry/mortar-calculator/): Mortar calculator for brickwork: brick count and mortar volume from wall area or your own count, at a 3/8 or 1/2 inch joint, with the masonry sand to match.
- [Stair Stringer Calculator](https://takeoffmetric.com/stairs/stair-stringer-calculator/): Stair stringer calculator: a measured total rise divided into risers, the treads, run, diagonal, layout line and throat that follow, and the 2x12 stock to buy.
- [Cubic Yard Calculator](https://takeoffmetric.com/measure/cubic-yard-calculator/): Cubic yard calculator for up to four areas of mixed shapes: cubic yards, feet and meters, the area a volume covers, dug-soil swell, and bags and truck trips.
- [Square Footage Calculator](https://takeoffmetric.com/measure/sqft-calculator/): Square footage calculator for up to six shapes with deductions, outside dimensions taken to the inside floor, a house measured the ANSI Z765 way, and boxes.
- [Duct Calculator](https://takeoffmetric.com/hvac/duct-calculator/): Duct calculator: round or rectangular size from airflow and your friction rate or velocity, rounded up to a stock size, what a duct carries, a reducing trunk.
- [Pipe Weight Calculator](https://takeoffmetric.com/plumbing/pipe-weight-calculator/): Pipe weight calculator: weight per foot or meter from OD and wall in carbon steel, stainless 316, aluminum 6061 or your density, full of water, total and cost.